Function Keys And Operation Procedures Instructions

Product Introduction

Principle of the product:

The SMD counter adopts the principle of photoelectric sensing,and uses the corresponding relation between the guide hole and the part, through the special-purpose processing chip and the large-scale centralized circuit processing, realizes the zero error, accurately measures the number of SMD parts, can realize the convenient and quick count, is the high efficiency auxiliary equipment of SMT material management.

Matters need attention

1.After unpacking, please check if all the attachments are complete.
2.Please read the operation manual carefully before using and keep it properly.
3.Check whether the voltage specification is consistent with that of municipal power.
4.Please make sure to connect the ground wire to ensure the safety of the
person and parts.

Function Keys And Operation Procedures Instructions

1）PRINT”
Operation method: press this button, the number of parts and quantities can
be counted by the barcode printer.
2）“SET”
If "00000" is displayed at the lower left corner of the display screen, you can directly press the number key to enter the number of parts to be calculated: press the "SET" key again to change to manual mode, and "****" is displayed at the lower left corner of the display screen. Manual and automatic modes are switched through this key. (note: the automatic mode is the preset value before the disk material, and the machine will stop automatically when it rotates to the set value. In the manual mode, the machine will stop only when the "stop/reset" key is pressed manually or all materials are finished.)
3）“PITCH”
Operation method: after pressing this button, the PITCH value of the display screen will flash, then input the spacing of materials, and then press the "ENTER" button to confirm. If no button is pressed for 5 seconds, the memory will be automatically memorized, and the sound of a drip will be returned to standby state.
4）“Positive direction/RIGHT”
Operation method: press this button to start counting parts in the positive direction, that is, the number shows a positive number or increases. When printing, press this button to move the cursor to the right to set the parameters.
5）“The opposite direction/LEFT”
Operation method: press this button to start counting parts in the opposite direction, that is, the number displays negative number or decreases. When printing, press this button to move the cursor to the left to set the parameters.
6）“STOP/RESET”
Operation method:
1.In the state of counting or returning, press this button to stop counting or returning.
2.In standby mode, press this button for more than two seconds to clear the COUNT value.
3.Press this button when printing the interface to return to the main interface.
4.Press this button to stop and return to the standby screen during selftest.
7）“ SELECT”
Operation method: in standby mode, press this button for 1 second, and the machine conducts self-check test; In automatic mode, press this key to clear the set number; Set the toggle button for the print interface parameters when printing.
8）“ LOSS”
Operation method: press this button to turn on or off the function of Leak hunting
9）“ TIME”
Operation method: this button is the switching key of motor speed. Press this button, and the LCD screen will switch between H(high speed), M(medium speed) and L(low speed).
10）“ENTER”
Operation method: when setting parameters in the print interface, press this button to save the parameters set.

Product specifications:

Power supply: AC220V,/A100V 50/60 HZ, 25W
Counting range: -99999- 99999PCS
Weight:10 kg

Product application:

The SMD material belt type components are all suitable
Diameter of belt wheel:Any size is all suitable
PITCH: 1,2,4,8,10,12,16,24,32,44,56 mm
WIDTH: 4,6,8,12,16,24,32,44,56mm (note: smaller or wider distance can be developed or customized according to demand)

Accept OEM/ODM

Dear customer, we make a lot of tapes in different colors and size, please send inquiry to us with your request tape size and color, we could show you our finished products and tape specification according to your usage.

KangHongJing is a professional production and sales factory that supports customization of colors, patterns, and packaging. Specializing in the research and development of SMT production workshop. I hope it can help you. If you want to know more about SMT assembly information, you can follow the updates of KangHongJing.

WhatsApp/Tel/WeChat: +86 135 3057 5115 E-mail: ceo@kanghongjin.com

Shenzhen Kanghongjin Electronics Co., Ltd.